Specifies the heavy bag filling packing machine (
The 'packing machine' for short)
The terms and definitions, types and basic parameters, requirements, test methods, inspection rule and marks, packaging, transport, and storage requirements.
This standard applies to the bag (
Woven bags, paper bags, etc. )
Filling more than 10 kg of makings, powder packing machine, widely used in chemical, food, medicine, agriculture, feed, additives and other industries.
1.
1 pneumatic pipe connection filling scale itself with the joint parts, user should provide greater than zero.
4 mpa, flow rate is more than 8 m3 / h dry, clean and high quality gas source, user with 8 mm tube access card sleeve joint.
According to the SF300H -
B type filling balance principle of pneumatic control diagram, check PV trachea and the ball valve, solenoid valve, air filtration pressure reducer.
Connection should be reliable, can not have loose or leakage phenomenon.
(
The pipe before delivery has good connection)
1.
2 electrical wiring connection (
1)
Power supply is 220 vac, 50 hz;
Filling balance all attachment (
In addition to the flame-proof control box inside the attachment)
And threading pipe shall be the responsibility of the user.
(
2)
According to the SF300H -
B type filling balance system of single-phase 220 v ac power supply control wiring diagram will be received the flame-proof control box input power terminal.
(
3)
If the users according to their own intend to adjust the position of the flame-proof control box should be in accordance with the SF300H -
B type filling balance system wiring diagram to connect all the flame-proof control box and balance between the connecting line.
(
4)
Grounding: use special grounding line will spray gun stents, flame-proof control box, controller, weighing platform, said, all roller grounding, grounding resistance less than 4 ohm.
1.
3 power to electricity and gas supply ¨ check mechanical installation is firm, each bolt and nut shall not loose.
¨ according to single-phase 220 v ac system wiring diagram will be received input from the flame-proof control box control power supply power terminal, single control power to electricity.
Attention!
Before to control on electricity, must be checked to ensure that all wiring all right!
Preparation (¨ ventilation
See below (
4)
) as is shown in
Figure Ø oil mist in the air handling the joint (
Sanlian pieces right a plastic cup)
Add lubricating oil, 2 types of oil viscosity.
5 to 7 ° E, such as anti-wear hydraulic oil (46
If with YCS type filling scale provide for two pieces, is not this step)
。
Ø anticlockwise sanlian pieces of the handwheel, make constant value spring unloading, then open the air supply, gradually turn the handwheel clockwise, pressure increase gradually, until the pressure gauge indicating pressure to need,
0.
5MPa±0.
1MPa)
When tighten brake knob;
And then adjust the lid down.
1.
1.
After 1 original position adjustment of gas supply of the actuator, the original location of the actuator are as follows: DN40 ball valve: cut DN15 ball valve material: to cut off the bottom valve cylinder material: inferior vena ventilation, bottom valve closed lifting cylinder: up close to the switch under the filling head office: when a can signal atresia lift if discover a primitive state of the actuator is wrong, but the corresponding electromagnetic valve on the switch in and out of the trachea (
Pay attention to when the pair of trachea, sanlian pieces of pressure should be adjusted to zero)
Or make the proximity switch near the filling head.
1.
1.
2 ball valve manual debugging by pressing the corresponding ball valve solenoid valve on the manual button operation, observe the ball valve movement situation, the ball valve action should be neatly and smooth.
Specific debugging, when as a ball valve action does not produce obvious clang is advisable.
Note: due to the system before delivery are real strict debugging, therefore, generally do not need to be adjusted at the user's site.
Jinzong Machinery, the main business products include liquid packaging automatic packaging equipment, automatic filling equipment specializing in the production of seller.
Products through the ISO9001:2000 quality system certification, is sinopec, petrochina and other qualified suppliers.
Jinzong Machinery LTD. Is a high-tech enterprise, at home.
'Benign, high consistency, high stability, high yields and excellent compatibility' is Jinzong Machinery manufacturing guidelines, the company passed the ISO9001 international quality system certification, ISO14001 environmental management system certification, the company's products are gradually through the 'CE'.
Jinzong Machinery, welcome the masses of customers came to negotiate.
Products are mainly applied materials: car paint, varnish, thinner, curing agent, pigment, paint, furniture paint, primer, exterior paint, industrial paint, all-purpose adhesive, glue, shoe glue, white latex, marble glue, resin, printing ink, pesticide, lube oil, atomic ash, ink, oil, etc.
。
。
Product scope of application:
chemical industry, paint, paint, adhesives, resins, chemical solvent, curing agent, lubricant, atomic ash, ceramic ink, battery materials, all kinds of ink, inkjet ink, daily chemical products and new materials
One increasingly popular managerial tactic to improve problem-solving performance of chemical reactor is to increase the connectedness, or what academics call clustering, of the organization
Boasting good reputation in the industry, Guangdong
Jinzong Machinery Co., Ltd. is the leading chemical reactor supplier, offering high quality and chemical reactor services for homes and enterprised all over the world. More info on Jinzong Machinery.
Time is one of the biggest challenges cited by manufacturing chemical reactor.
Guangdong Jinzong Machinery Co., Ltd. have been an established and popular company with an excellent track record for the best customer satisfaction.
