In order to realize the heating, evaporation, cooling and low and high speed mixing reaction required by the process, the reactor is an essential equipment. However, if the maintenance of the reactor is not in place, it often causes safety and environmental pollution accidents, which should be paid attention to in use. 01 Requirements for plant location: the reactor shall be installed in the operation room meeting the safety requirements for hazardous chemicals production, and each operation room shall be provided with access and outlet to the outside, so as to ensure good ventilation of the equipment. 02 Installation requirements: after opening the package, check whether the equipment is damaged, install the equipment according to the equipment model and structural drawing, and check the equipped parts according to the packing list. Pay attention to the heating and cooling methods and media meet the process requirements, and the installation should meet the relevant safety specifications. 03 Sealing Maintenance: the sealing condition of the chemical reactor is very critical, which directly affects the use effect and production safety, and is also the most important part of the equipment. Therefore, it is necessary to pay attention to check the sealing parts according to the operation manual, and keep the lubrication or cooling medium to meet the requirements. Once the leakage is found, stop the machine immediately for inspection and maintenance, and then put it into use again after passing the pressure maintaining test without leakage. 04 Maintenance of instruments and meters: at ordinary times, it is necessary to pay attention to the cleaning of measuring parts such as instruments and sensors, maintain the sensitivity of sensors, and carry out regular calibration and verification according to the specification requirements, conduct fastening inspection on the contact parts of connecting lines, and conduct regular inspection on the integrity of shielding devices. 05 Maintenance of process valve system: pay attention to the action sensitivity of each process valve to ensure the normal operation of valve actuator and avoid blockage. Once any abnormality is found, it is recommended to replace it. 06 Maintenance of mixing system: observe the operation at any time, stop the machine for inspection in case of abnormal noise or vibration, pay special attention to the lubrication and temperature rise of each bearing point, inform the supplier for inspection and treatment in case of abnormality, and replace the lubricating oil regularly and tighten the connecting bolts at any time. It can also make early warning by online monitoring system load change through jinzong Internet of things system. 07 Maintenance of safety devices: ensure the use of safety devices in accordance with safety regulations, and strictly control the phenomenon of blockage and failure. Regular inspection to relevant departments. 08 Maintenance of automatic control system: ensure stable power supply, normal signal feedback and sensitive action of actuator. Do a good job in lightning protection, surge protection and electrostatic interference prevention measures, do not plug in and out various modules at will, pay attention to the optical brazing and other signal lines, do not be suppressed and interfered by other process pipelines and power cables, such as WiFi signal transmission, you are welcome to check the signal source and transmission quality frequently. 09 Shutdown for production treatment: after each use, the reaction kettle body shall be cleaned, the process pipeline shall be emptied, and the relevant filtering devices shall be cleaned. If the anti-corrosion conditions are involved, the cleaning and protection shall be done in time according to the anti-corrosion requirements. When it is put into use again, it is necessary to conduct a comprehensive inspection of the system and equipment, and the trial run can be put into production only after the normal operation.  

The application of enamel and stainless steel reactor equipment is very wide, whether it is a complete set of resin plant, adhesive equipment, polymer reactor,solvent production equipment in the chemical industry, or API and intermediate synthesis equipment in the pharmaceutical industry, or the new energy industryAnode material equipment, or various mixing and dispersing equipment in the coating industry and agitation and mixing equipment in the cosmetics industry, are inseparable from the reactor.The power heart of the reactor is the electric motor. If you choose an inappropriate motor, it will directly affect the production schedule or damage the equipment. Today, the Jinzong mechanical reactor manufacturer tells you several key points when choosing a reactor motor:1.Power selectionDetermine the torque according to the maximum viscosity of the material (the reaction is dynamic and the viscosity will also change), the density of the material, the solid content ratio of the material, the diameter of the blade of the agitator, the structure of the blade, the cross-sectional area of the front, the speed of stirring, the impact load, etc. And calculate the safety margin at more than 0.5 times the maximum torque, and finally determine the corresponding stirring motor power to ensure the normal application and service life of the equipment.2. Choice of speedAccording to the mixing speed and torque requirements of the application, the matching selection of the appropriate motor and reducer is carried out, and the selection of the motor speed is finally determined.3. Selection of safety protection levelThis is also very important. Choose the safety protection level of the motor according to the safety level requirements of the use occasion, site environment, material characteristics, etc. Generally, most reactors need to be equipped with intrinsically safe explosion-proof motors.Practical requirements can ensure safe use.4. Choice of installation methodAccording to the conditions of the workshop and equipment layout requirements, the vertical or horizontal installation structure should be selected, and the connection form with the reducer should also be considered.5. The requirements of the control system for the motorIt is necessary to select different special motors according to the starting mode, stopping requirements, speed regulation mode, etc., especially for the occasions that are running at low speed for a long time or have start-stop requirements.6. The requirements of electric power supply for motorsThe selection of rated voltage and frequency should be made according to the local power supply configuration.Selection of energy consumption levels, use verification standards and other requirements, etc.

A smart paint production line! Realize 90% production automation in chemical plants! Intelligent manufacturing is not a simple automatic production, it is a revolutionary industrial production method, not only need intelligent factory environment, to realize the digitalization of production management of the whole enterprise, but also have Internet of things technology. There is no doubt that intelligence is the development direction of manufacturing automation. Artificial intelligence technology is widely used in almost all aspects of the manufacturing process.In order to respond to the China national development strategy of intelligent manufacturing, Jinzong machinery has been researching and developing from the aspect of how to effectively connect the "structure and control system of equipment" with the Internet of things system since 2016, and has successfully developed the latest generation of automatic production line system, which is a real system with the function of Internet of things, and will open up one of the key nodes for the realization of intelligent manufacturing.Among them, jinzong automatic water-based coating equipment is a significant achievement. This system uses automatic production process, from feeding to discharging is mainly completed by computer operation, most of the processes are closed automatic operation, at the same time, it also avoids the harm of chemical substances to human body, and achieves time-saving, labor-saving, energy saving and environmental protection to the greatest extent. And for customers, design, production, installation, commissioning of the annual output of 10000 tons of paint complete sets of equipment. One machine, double cylinder, high speed dispersion, pulping kettle with weighing system, automatic feeding of liquid materials and additives, step-by-step grinding, finished product filtration, automatic filling, sewage and other processes. The complete set of equipment can produce not only water-based industrial paint, water-based wood paint, but also oil-based automobile paint, texture paint, etc. The layout is reasonable and easy to operate, which realizes the seamless combination of semi-automatic and manual operation. As a veteran manufacturer of coatings and new energy equipment, jinzong machinery has witnessed the transformation and development of the coating industry in the past 20 years. In the past 20 years, jinzong machinery has been carrying out research, development, manufacturing and system integration of equipment manufacturing industry around "chemical industry", including automatic metering system, automatic feeding system, high-efficiency mixing, dispersion and grinding system, and automatic circulation production system , industrial color matching system, automatic filling, packaging and storage system, intelligent formula management system with invention patent, intelligent production operation system with invention patent.Recently, the automatic control system of the styrene acrylic emulsion production line produced by Jin Zong machinery began to be applied in Egypt. The system is based on the resin production control system of SIEMENS S7-300 system. After market research and continuous development and innovation, the 90% production automation is realized through the independent formulation process management system.Through years of exploration and development, with a sound quality assurance system, jinzong machinery has a high-quality technical team, experienced quality inspection personnel, excellent processing equipment, mature welding technology, advanced manufacturing technology and perfect detection means. Jinzong enterprise strictly abides by the tenet of "service first, reputation first", strives to improve various service systems, adheres to the principle of "mutual benefit and win-win", and always adheres to the spirit of "development, innovation and truth-seeking", and has won a good reputation from the majority of users.

Main Performance Characteristics Of High Shear EmulsifierA high shear emulsifier is one that distributes one or more phases into another continuous phase efficiently, quickly, and uniformly, and in the usual case, the phases are mutually insoluble. Due to the high tangential speed and high-frequency mechanical effects generated by the high-speed rotation of the rotor, the material is subjected to strong mechanical and hydraulic shear, centrifugal extrusion, liquid layer friction and impact in the narrow gap between the stator and the rotor. The combined effects of tearing and turbulence, so that the incompatible solid phase, liquid phase and gas phase are uniformly and finely dispersed and emulsified under the action of the corresponding mature process and appropriate amount of additives, and finally stabilized after high frequency reciprocation. High quality products.1. Also known as centrifugal homogenizer, it is especially suitable for the pre-treatment section of materials;2. It has large processing capacity and low energy consumption, and is suitable for industrialized continuous production;3. The treated material has the characteristics of narrow particle distribution range and good uniformity;4. Time saving, high efficiency, energy saving and high production efficiency;5. Easy to install and disassemble, easy to clean, to meet the CIP cleaning needs of different occasions;6. Has a certain self-suction and low lift conveying function;7. No dead ends, 100% of the material is dispersed by emulsification;8. Low noise, stable operation and easy maintenance.It can be divided into one-way and two-way working modes from the suction mode;From the discharge mode, it can be divided into the working mode of radial flow and axial flow;The rotor structure is further divided into a slotted ring type, a closed groove ring type, a four straight blade rotor, a three curved blade rotor, and a multi-layer open (closed) groove ring type;The stator structure is further divided into a straight slot open type, a straight slot closed type, a chute open type, a chute closed type, a mesh hole, a round hole, and a plurality of layers;From the work sealing requirements are divided into open (suspended, kettle) type, with sealed vacuum emulsifier (machine seal, water seal, oil seal, magnetic drive seal);The closed-type rotating stator adopts precision matching, and the slotted rotating stator generally has a slightly larger clearance.The rotor and stator of the emulsifier head are usually manufactured from forged parts and thus have excellent overall mechanical properties. It has high shear, dispersion, homogenization and emulsifying efficiency. The cutting head is composed of a rotor and a stator, wherein the rotor has strong kinetic energy with its extremely high linear velocity and high-frequency mechanical effect, so that the material is subjected to shearing, centrifugal extrusion, liquid layer friction in the precise gap between the rotating and the stator, A combination of impact tearing and turbulence to achieve dispersion, grinding, and emulsification.